O Scale	Wargaming	Architectural	Narrow Gauge	Tools+

Model Railway Modules & Transformers

All instructions are in PDF format, so you will need Adobe Acrobat to read them.  Click on the logo below to download it to your computer.

Model HF-1 - Single Track Cleaner

Electronic Automatic Single Track Cleaner for use with all types of controllers.  The unit superimposes a harmless high frequency signal over the output from the controller.  When a poor contact between loco and rail is detected the unit switches on, ionising the gap and burning off the dirt, switching off again when contact is restored.
Input:	16v A.C. at a maximum of 1.25 amps (Gaugemaster T1 or M1 recommended)
Specification:	The HF-1 is compatible with the SS-1, SS-2 and SS-3
Measurements:	75mm x 60mm x 27mm
Price:	Only £45.00
	Click here for technical information.
Model HF-2 - Twin Track Cleaner
Electronic Automatic Twin Track Cleaner for use with all types of controllers.  This unit works in the same way as the single track unit above, with the facility for a second track.
Input: Measurements:	16v A.C. at a maximum of 1.25 amps (Gaugemaster T1 or M1 recommended) 109mm x 68mm x 20mm
Specification:	The HF-2 is compatible with the SS-1, SS-2 and SS-3
Price:	Only £60.00
	Click here for technical information.
Model SS-1 - Super Shuttle
A time controlled unit which can be used with any controller and stops a locomotive at a point on a line, reverses it and then stops it again at a second point, reversing the locomotive again.  This repeats indefinitely.  The duration of each sequence can be adjusted from approx 20-70 seconds.
Input:	16v A.C. at a maximum of 1.25 amps (Gaugemaster T1 or M1 recommended)
Measurements:	109mm x 68mm x 20mm
Price:	Only £45.00
	Click here for technical information.
Model SS-2 - Station Stop
A small unit providing an automatic stop and start facility which only requires one reed switch to be installed.  The locomotive decelerates for about 5 seconds after passing the reed switch and stops for approximately 20 seconds as factory set.  The time stopped can be adjusted from approx 20-70 seconds, the rate of deceleration is also adjustable.  Reed switch and magnet are included.
Input:	16v A.C. at a maximum of 1.25 amps (Gaugemaster T1 or M1 recommended)
Measurements:	109mm x 68mm x 20mm
Price:	Only £55.00
	Click here for technical information.
Transformers
Also on this page:  Modules  Point Control
Model M1 - Cased Transformer
Mains Transformer - fully cased, plugged and output protected with circuit breakers, these transformers are virtually ready to use straight from the box.  All you need to do is connect it to the units you want to power. This unit is also suitable for the CDU (Capacitor Discharge Unit) for 16v applications (Peco/ Hornby/ Seep point motors)
Input:	Mains (240v A.C.) use 3 amp fuse
Output:	2 x 16v A.C at 1 amp each
Measurements:	99mm x 75mm x 65mm
Can be used to power the following panel mounted controllers:
100,  U,  UD,  UDS,  UTS,  UQ,  UF,  UDF
Can be used to power the following Handheld controllers:
W,  WS,  HH
Can be used to power the following modules:
HF-1,  HF-2,  HF-3,  SS-1,  SS-2,  SS-3
Price:	Only £75.00
Cased transformers are available in other specifications.  These are models M2, designed for O Gauge, M3, designed for use with the CDU, and M4, designed for Z Gauge and Lighting.
Model T1 - Open Construction Transformer
Open Construction Transformers are not supplied with mains leads or circuit breakers, but are designed for those who are constructing their own control panels and do not want a cased transformer.  This unit is designed to power panel controllers for N, OO and most small gauges. This unit is also suitable for the CDU (Capacitor Discharge Unit) for 16v applications (Peco/ Hornby/ Seep point motors) A fitting kit is available for this transformer.
Input:	Mains (240v AC) use 3 amp fuse. Requires own mains lead & plug to be fitted
Output:	2 x 16v AC at 1.25 amps each.  Requires own wires and cutouts as necessary. GM41 Thermal Cutouts can be used for this transformer.
Price:	Only £35.00
Model T2 - Open Construction Transformer
Open Construction Transformer.  As the T1 transformer, above, but with a different power rating.  This unit is ideal for use with O Gauge controllers. A fitting kit is available for this transformer.
Input:	Mains (240v AC) use 3 amp fuse Requires own mains lead & plug to be fitted
Output:	1 x 18v A.C. at 2.5 amps (for 'O' Gauge) Requires own wires and cutouts as necessary. GM42 Thermal Cutouts can be used for this transformer.
Price:	Only £35.00
This model is also available as a cased transformer, the M2
Model T3 - Open Construction Transformer
Open Construction Transformer.  As the T1 transformer, above, but with a different power rating.  This unit may be used with the CDU (Capacitor Discharge Unit) for 24v applications. A fitting kit is available for this transformer.
Input:	Mains (240v A.C.) use 3 amp fuse Requires own mains lead & plug to be fitted
Output:	1 x 24v A.C. at 1.25 amps Requires own wires and cutouts as necessary. GM41 Thermal Cutouts can be used for this transformer.
Price:	Only £35.00
This model is also available as a cased transformer, the M3
Model T4 - Open Construction Transformer
Open Construction Transformer.  As the T1 transformer, above, but with a different power rating.  This unit is designed for use with Z gauge controllers and lighting. A fitting kit is available for this transformer.
Input:	Mains (240v A.C.) use 3 amp fuse Requires own mains lead & plug to be fitted
Output:	2 x 12v A.C. at 1.25 amps Requires own wires and cutouts as necessary. GM41 Thermal Cutouts can be used for this transformer.
Price:	Only £35.00
This model is also available as a cased transformer, the M4
Point Control
Also on this page:  Electronic Modules  Transformers
Model CDU - Capacitor Discharge Unit
For operating heavy duty point motors.  The unit stores up power in capacitors and when a point motor is actuated, discharges in one big punch giving the point motor a firm and positive switching action.  Connected to points via switches or probe and studs.  Prevents burnt out motors.
Input:	16v to 24v A.C. at a maximum of 2.5 amps Gaugemaster T1 for Hornby/ Peco/ Seep point motors or T3 for 24v applications.
Price:	Only £18.75
	Click here for technical information.
Model PCU2 - Point Control Slave Unit
Slave Point Control Unit for use with most Gauges
Input:	From PCU-1 or a Discharge Unit
Output:	As PCU-1 and can be extended to another PCU-2
Specification:	Point Control Unit for up to 21 point motors for use with PCU-1  Can also be used with T3 or M3 Transformer and a CDU
Measurements:	Box: 110mm x 55mm x 20mm Overall: 110mm x 53mm x 39mm
Price:	Only £50.00
	Click here for technical information.

We are always looking to make improvements to our website to try and improve the quality of your visit.  We would welcome your feedback and suggestions, so please do not hesitate to e-mail our webmaster with your comments.  Alternatively call us on 01903 884488.

Home  Cookies  Privacy Statement  Terms & Conditions  Site Map  Site Guide
WEEE Regulations  Glossary  Careers & Jobs

Tel –  +44 (0) 1903 884488  Fax –  +44 (0) 1903 884377  E-Mail us –  click here

Gaugemaster.com is a trading name of Gaugemaster Controls Ltd.
Registered in England No. 2714470, Registered office:
Gaugemaster House, Ford Road
Arundel, West Sussex, BN18 0BN, United Kingdom

VAT Reg. No. 587 8089 71

Copyright © 2003-2014 Gaugemaster Controls Ltd. All Rights Reserved.